CAT93C56, CAT93C57 2-Kb Microwire Serial CMOS EEPROM Description The CAT93C56/57 is a 2-kb CMOS Serial EEPROM device which is organized as either 128 registers of 16 bits (ORG pin at VCC) or 256 registers of 8 bits (ORG pin at GND). Each register can be written (or read) serially by using the DI (or DO) pin. The CAT93C56/57 features sequential read and self-timed internal write with auto-clear. On-chip Power-On Reset circuitry protects the internal logic against powering up in the wrong state. Features * * * * * * * * * * * * High Speed Operation: 2 MHz 1.8 V to 5.5 V Supply Voltage Range Selectable x8 or x16 Memory Organization Sequential Read Software Write Protection Power-up Inadvertant Write Protection Low Power CMOS Technology 1,000,000 Program/Erase Cycles 100 Year Data Retention Industrial and Extended Temperature Ranges 8-pin PDIP, SOIC, TSSOP and 8-pad TDFN Packages These Devices are Pb-Free, Halogen Free/BFR Free and are RoHS Compliant VCC ORG CS SK CAT93C56 CAT93C57 http://onsemi.com SOIC-8 V or W SUFFIX CASE 751BD SOIC-8 EIAJ X SUFFIX CASE 751BE TDFN-8 VP2 SUFFIX CASE 511AK PDIP-8 L SUFFIX CASE 646AA TDFN-8 ZD4 SUFFIX CASE 511AL TSSOP-8 Y SUFFIX CASE 948AL PIN CONFIGURATIONS 1 CS SK DI DO VCC NC ORG GND PDIP (L), SOIC (V, X), TSSOP (Y), TDFN (VP2, ZD4*) NC VCC CS SK ORG GND DO DI 1 SOIC (W*) (Top Views) * TDFN 3x3 mm (ZD4) and SOIC (W) rotated pin-out packages are available for CAT93C57 and CAT93C56, Rev. E only (not recommended for new designs of CAT93C56) DO PIN FUNCTION DI Pin Name GND Figure 1. Functional Symbol NOTE: When the ORG pin is connected to VCC, the x16 organization is selected. When it is connected to ground, the x8 pin is selected. If the ORG pin is left unconnected, then an internal pullup device will select the x16 organization. Function CS Chip Select SK Clock Input DI Serial Data Input DO Serial Data Output VCC Power Supply GND Ground ORG Memory Organization NC No Connection ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 16 of this data sheet. (c) Semiconductor Components Industries, LLC, 2009 August, 2009 - Rev. 18 1 Publication Order Number: CAT93C56/D CAT93C56, CAT93C57 Table 1. ABSOLUTE MAXIMUM RATINGS Parameters Ratings Units Storage Temperature -65 to +150 C Voltage on Any Pin with Respect to Ground (Note 1) -0.5 to +6.5 V Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. The DC input voltage on any pin should not be lower than -0.5 V or higher than VCC + 0.5 V. During transitions, the voltage on any pin may undershoot to no less than -1.5 V or overshoot to no more than VCC + 1.5 V, for periods of less than 20 ns. Table 2. RELIABILITY CHARACTERISTICS (Note 2) Parameter Symbol NEND (Note 3) TDR Endurance Data Retention Min Units 1,000,000 Program / Erase Cycles 100 Years 2. These parameters are tested initially and after a design or process change that affects the parameter according to appropriate AEC-Q100 and JEDEC test methods. 3. Block Mode, VCC = 5 V, 25C Table 3. D.C. OPERATING CHARACTERISTICS, CAT93C56, Die Rev. G - New Product (VCC = +1.8 V to +5.5 V, TA=-40C to +125C unless otherwise specified.) Symbol Parameter Test Conditions Min Max Units ICC1 Power Supply Current (Write) fSK = 1 MHz, VCC = 5.0 V 1 mA ICC2 Power Supply Current (Read) fSK = 1 MHz, VCC = 5.0 V 500 mA ISB1 Power Supply Current (Standby) (x8 Mode) VIN = GND or VCC, CS = GND ORG = GND TA = -40C to +85C 2 mA TA = -40C to +125C 4 Power Supply Current (Standby) (x16 Mode) VIN = GND or VCC, CS = GND ORG = Float or VCC TA = -40C to +85C 1 TA = -40C to +125C 2 TA = -40C to +85C 1 TA = -40C to +125C 2 TA = -40C to +85C 1 TA = -40C to +125C 2 ISB2 VIN = GND to VCC mA ILI Input Leakage Current ILO Output Leakage Current VOUT = GND to VCC, CS = GND VIL1 Input Low Voltage 4.5 V v VCC < 5.5 V -0.1 0.8 V VIH1 Input High Voltage 4.5 V v VCC < 5.5 V 2 VCC + 1 V VIL2 Input Low Voltage 1.8 V v VCC < 4.5 V 0 VCC x 0.2 V VCC x 0.7 VCC + 1 V 0.4 V VIH2 Input High Voltage 1.8 V v VCC < 4.5 V VOL1 Output Low Voltage 4.5 V v VCC < 5.5 V, IOL = 2.1 mA VOH1 Output High Voltage 4.5 V v VCC < 5.5 V, IOH = -400 mA VOL2 Output Low Voltage 1.8 V v VCC < 4.5 V, IOL = 1 mA VOH2 Output High Voltage 1.8 V v VCC < 4.5 V, IOH = -100 mA 2.4 http://onsemi.com 2 mA V 0.2 VCC - 0.2 mA V V CAT93C56, CAT93C57 Table 4. D.C. OPERATING CHARACTERISTICS, CAT93C56/57, Die Rev. E - Mature Product (CAT93C56, Rev. E - NOT RECOMMENDED FOR NEW DESIGNS) (VCC = +1.8 V to +5.5 V, TA=-40C to +125C unless otherwise specified.) Parameter Symbol Test Conditions Min Max Units ICC1 Power Supply Current (Write) fSK = 1 MHz, VCC = 5.0 V 3 mA ICC2 Power Supply Current (Read) fSK = 1 MHz, VCC = 5.0 V 500 mA ISB1 Power Supply Current (Standby) (x8 Mode) VIN = GND or VCC, CS = GND ORG = GND 10 mA ISB2 Power Supply Current (Standby) (x16 Mode) VIN = GND or VCC, CS = GND ORG = Float or VCC 10 mA VIN = GND to VCC 1 mA VOUT = GND to VCC, CS = GND 1 mA ILI Input Leakage Current ILO Output Leakage Current VIL1 Input Low Voltage 4.5 V v VCC < 5.5 V -0.1 0.8 V VIH1 Input High Voltage 4.5 V v VCC < 5.5 V 2 VCC + 1 V VIL2 Input Low Voltage 1.8 V v VCC < 4.5 V 0 VCC x 0.2 V VCC x 0.7 VCC + 1 V 0.4 V VIH2 Input High Voltage 1.8 V v VCC < 4.5 V VOL1 Output Low Voltage 4.5 V v VCC < 5.5 V, IOL = 2.1 mA VOH1 Output High Voltage 4.5 V v VCC < 5.5 V, IOH = -400 mA VOL2 Output Low Voltage 1.8 V v VCC < 4.5 V, IOL = 1 mA VOH2 Output High Voltage 1.8 V v VCC < 4.5 V, IOH = -100 mA 2.4 V 0.2 VCC - 0.2 V V Table 5. PIN CAPACITANCE (TA = 25C, f = 1 MHz, VCC = 5 V) Symbol COUT (Note 4) CIN (Note 4) Test Conditions Output Capacitance (DO) Input Capacitance (CS, SK, DI, ORG) Max Units VOUT = 0 V Min Typ 5 pF VIN = 0 V 5 pF 4. These parameters are tested initially and after a design or process change that affects the parameter according to appropriate AEC-Q100 and JEDEC test methods. http://onsemi.com 3 CAT93C56, CAT93C57 Table 6. A.C. CHARACTERISTICS (Note 5), CAT93C56, Die Rev. G - New Product (VCC = +1.8V to +5.5V, TA = -40C to +125C, unless otherwise specified.) Limits Min Parameter Symbol tCSS CS Setup Time tCSH tDIS Max Units 50 ns CS Hold Time 0 ns DI Setup Time 100 ns tDIH DI Hold Time 100 ns tPD1 Output Delay to 1 0.25 ms tPD0 Output Delay to 0 0.25 ms Output Delay to High-Z 100 ns 5 ms tHZ (Note 6) tEW Program/Erase Pulse Width tCSMIN Minimum CS Low Time 0.25 ms tSKHI Minimum SK High Time 0.25 ms tSKLOW Minimum SK Low Time 0.25 ms tSV Output Delay to Status Valid SKMAX Maximum Clock Frequency DC 0.25 ms 2000 kHz Table 7. A.C. CHARACTERISTICS (Note 5), CAT93C56/57, Die Rev. E - Mature Product (CAT93C56 Rev. E - NOT RECOMMENDED FOR NEW DESIGNS) Limits VCC = 1.8 V - 5.5 V Symbol Parameter Min VCC = 2.5 V - 5.5 V Max Min Max VCC = 4.5 V - 5.5 V Min Max Units tCSS CS Setup Time 200 100 50 ns tCSH CS Hold Time 0 0 0 ns tDIS DI Setup Time 400 200 100 ns 400 tDIH DI Hold Time tPD1 Output Delay to 1 1 0.5 0.25 ms tPD0 Output Delay to 0 1 0.5 0.25 ms Output Delay to High-Z 400 200 100 ns Program/Erase Pulse Width 10 10 10 ms tHZ (Note 6) tEW 200 100 ns tCSMIN Minimum CS Low Time 1 0.5 0.25 ms tSKHI Minimum SK High Time 1 0.5 0.25 ms tSKLOW Minimum SK Low Time 1 0.5 0.25 ms tSV Output Delay to Status Valid SKMAX Maximum Clock Frequency 1 DC 250 0.5 DC 500 DC 0.25 ms 1000 kHz Table 8. POWER-UP TIMING (Notes 6 and 7) Symbol Parameter Max Units tPUR Power-up to Read Operation 1 ms tPUW Power-up to Write Operation 1 ms 5. Test conditions according to "A.C. Test Conditions" table. 6. These parameters are tested initially and after a design or process change that affects the parameter according to appropriate AEC-Q100 and JEDEC test methods. 7. tPUR and tPUW are the delays required from the time VCC is stable until the specified operation can be initiated. http://onsemi.com 4 CAT93C56, CAT93C57 Table 9. A.C. TEST CONDITIONS Input Rise and Fall Times 50 ns Input Pulse Voltages 0.4 V to 2.4 V 4.5 V v VCC v 5.5 V Timing Reference Voltages 0.8 V, 2.0 V 4.5 V v VCC v 5.5 V Input Pulse Voltages 0.2 VCC to 0.7 VCC 1.8 V v VCC v 4.5 V Timing Reference Voltages 0.5 VCC 1.8 V v VCC v 4.5 V Output Load Current Source IOLmax/IOHmax; CL=100 pF Device Operation The CAT93C56/57 is a 2048-bit nonvolatile memory intended for use with industry standard microprocessors. The CAT93C56/57 can be organized as either registers of 16 bits or 8 bits. When organized as X16, seven 10-bit instructions for 93C57 or seven 11-bit instructions for 93C56 control the reading, writing and erase operations of the device. When organized as X8, seven 11-bit instructions for 93C57 or seven 12-bit instructions for 93C56 control the reading, writing and erase operations of the device. The CAT93C56/57 operates on a single power supply and will generate on chip, the high voltage required during any write operation. Instructions, addresses, and write data are clocked into the DI pin on the rising edge of the clock (SK). The DO pin is normally in a high impedance state except when reading data tSKHI from the device, or when checking the ready/busy status after a write operation. The serial communication protocol follows the timing shown in Figure 2. The ready/busy status can be determined after the start of internal write cycle by selecting the device (CS high) and polling the DO pin; DO low indicates that the write operation is not completed, while DO high indicates that the device is ready for the next instruction. If necessary, the DO pin may be placed back into a high impedance state during chip select by shifting a dummy "1" into the DI pin. The DO pin will enter the high impedance state on the rising edge of the clock (SK). Placing the DO pin into the high impedance state is recommended in applications where the DI pin and the DO pin are to be tied together to form a common DI/O pin. tSKLOW tCSH SK tDIH tDIS VALID VALID DI tCSS CS tDIS tPD0, tPD1 DO DATA VALID Figure 2. Synchronous Data Timing http://onsemi.com 5 tCSMN CAT93C56, CAT93C57 The format for all instructions sent to the device is a logical "1" start bit, a 2-bit (or 4-bit) opcode, 7-bit address (CAT93C57) / 8-bit address (CAT93C56) (an additional bit when organized X8) and for write operations a 16-bit data field (8-bit for X8 organizations). The instruction format is shown in Instruction Set table. Table 10. INSTRUCTION SET Address Data Instruction Device Type Start Bit READ 93C56 (Note 8) 1 10 A8-A0 A7-A0 93C57 1 10 A7-A0 A6-A0 93C56 (Note 8) 1 11 A8-A0 A7-A0 93C57 1 11 A7-A0 A6-A0 93C56 (Note 8) 1 01 A8-A0 A7-A0 D7-D0 D15-D0 93C57 1 01 A7-A0 A6-A0 D7-D0 D15-D0 93C56 (Note 8) 1 00 11XXXXXXX 11XXXXXX 93C57 1 00 11XXXXXX 11XXXXX 93C56 (Note 8) 1 00 00XXXXXXX 00XXXXXX 93C57 1 00 00XXXXXX 00XXXXX 93C56 (Note 8) 1 00 10XXXXXXX 10XXXXXX 93C57 1 00 10XXXXXX 10XXXXX 93C56 (Note 8) 1 00 01XXXXXXX 01XXXXXX D7-D0 D15-D0 93C57 1 00 01XXXXXX 01XXXXX D7-D0 D15-D0 ERASE WRITE EWEN EWDS ERAL WRAL Opcode x8 x16 x8 x16 Comments Read Address AN-A0 Clear Address AN-A0 Write Address AN-A0 Write Enable Write Disable Clear All Addresses Write All Addresses 8. Address bit A8 for 256x8 organization and A7 for 128x16 organization are "Don't Care" bits, but must be kept at either a "1" or "0" for READ, WRITE and ERASE commands. http://onsemi.com 6 CAT93C56, CAT93C57 Read data word is preceeded by a dummy zero bit. All subsequent data words will follow without a dummy zero bit. The READ instruction timing is illustrated in Figure 3. Upon receiving a READ command and an address (clocked into the DI pin), the DO pin of the CAT93C56/57 will come out of the high impedance state and, after sending an initial dummy zero bit, will begin shifting out the data addressed (MSB first). The output data bits will toggle on the rising edge of the SK clock and are stable after the specified time delay (tPD0 or tPD1). For the CAT93C56/57, after the initial data word has been shifted out and CS remains asserted with the SK clock continuing to toggle, the device will automatically increment to the next address and shift out the next data word in a sequential READ mode. As long as CS is continuously asserted and SK continues to toggle, the device will keep incrementing to the next address automatically until it reaches to the end of the address space, then loops back to address 0. In the sequential READ mode, only the initial Erase/Write Enable and Disable The CAT93C56/57 powers up in the write disable state. Any writing after power-up or after an EWDS (erase/write disable) instruction must first be preceded by the EWEN (erase/write enable) instruction. Once the write instruction is enabled, it will remain enabled until power to the device is removed, or the EWDS instruction is sent. The EWDS instruction can be used to disable all CAT93C56/57 write and erase instructions, and will prevent any accidental writing or clearing of the device. Data can be read normally from the device regardless of the write enable/disable status. The EWEN and EWDS instructions timing is shown in Figure 4. SK CS AN DI 1 1 AN-1 Don't Care A0 0 tPD0 HIGH-Z DO Dummy 0 D15 . . . D0 or D7 . . . D0 Address + 1 D15 . . . D0 or D7 . . . D0 Address + 2 D15 . . . D0 or D7 . . . D0 Figure 3. READ Instruction Timing SK STANDBY CS DI 1 0 0 * * ENABLE = 11 DISABLE = 00 Figure 4. EWEN/EWDS Instruction Timing http://onsemi.com 7 Address + n D15 . . . or D7 . . . CAT93C56, CAT93C57 Write Erase After receiving a WRITE command (Figure 5), address and the data, the CS (Chip Select) pin must be deselected for a minimum of tCSMIN. The falling edge of CS will start the self clocking clear and data store cycle of the memory location specified in the instruction. The clocking of the SK pin is not necessary after the device has entered the self clocking mode. The ready/busy status of the CAT93C56/57 can be determined by selecting the device and polling the DO pin. Since this device features Auto-Clear before write, it is NOT necessary to erase a memory location before it is written into. Upon receiving an ERASE command and address, the CS (Chip Select) pin must be deasserted for a minimum of tCSMIN (Figure 6). The falling edge of CS will start the self clocking clear cycle of the selected memory location. The clocking of the SaK pin is not necessary after the device has entered the self clocking mode. The ready/busy status of the CAT93C56/57 can be determined by selecting the device and polling the DO pin. Once cleared, the content of a cleared location returns to a logical "1" state. SK tCSMIN CS STATUS VERIFY AN DI 1 0 AN-1 A0 DN STANDBY D0 1 tSV BUSY HIGH-Z DO READY tHZ HIGH-Z tEW Figure 5. Write Instruction Timing SK CS STATUS VERIFY AN DI 1 1 AN-1 tCS A0 1 tSV DO STANDBY HIGH-Z tHZ BUSY tEW Figure 6. Erase Instruction Timing http://onsemi.com 8 READY HIGH-Z CAT93C56, CAT93C57 Erase All Write All Upon receiving an ERAL command (Figure 7), the CS (Chip Select) pin must be deselected for a minimum of tCSMIN. The falling edge of CS will start the self clocking clear cycle of all memory locations in the device. The clocking of the SK pin is not necessary after the device has entered the self clocking mode. The ready/busy status of the CAT93C56/57 can be determined by selecting the device and polling the DO pin. Once cleared, the contents of all memory bits return to a logical "1" state. Upon receiving a WRAL command and data, the CS (Chip Select) pin must be deselected for a minimum of tCSMIN (Figure 8). The falling edge of CS will start the self clocking data write to all memory locations in the device. The clocking of the SK pin is not necessary after the device has entered the self clocking mode. The ready/busy status of the CAT93C56/57 can be determined by selecting the device and polling the DO pin. It is not necessary for all memory locations to be cleared before the WRAL command is executed. SK CS STATUS VERIFY STANDBY tCS DI 1 0 1 0 0 tSV tHZ HIGH-Z DO BUSY READY HIGH-Z tEW Figure 7. ERAL Instruction Timing SK CS STATUS VERIFY STANDBY tCSMIN DI 1 0 0 0 1 DN D0 tSV tHZ BUSY DO tEW Figure 8. WRAL Instruction Timing http://onsemi.com 9 READY HIGH-Z CAT93C56, CAT93C57 PACKAGE DIMENSIONS PDIP-8, 300 mils CASE 646AA-01 ISSUE A SYMBOL MIN NOM A E1 5.33 A1 0.38 A2 2.92 3.30 4.95 b 0.36 0.46 0.56 b2 1.14 1.52 1.78 c 0.20 0.25 0.36 D 9.02 9.27 10.16 E 7.62 7.87 8.25 E1 6.10 6.35 7.11 e PIN # 1 IDENTIFICATION MAX 2.54 BSC eB 7.87 L 2.92 10.92 3.30 3.80 D TOP VIEW E A2 A A1 c b2 L e eB b SIDE VIEW END VIEW Notes: (1) All dimensions are in millimeters. (2) Complies with JEDEC MS-001. http://onsemi.com 10 CAT93C56, CAT93C57 PACKAGE DIMENSIONS SOIC 8, 150 mils CASE 751BD-01 ISSUE O E1 E SYMBOL MIN A 1.35 1.75 A1 0.10 0.25 b 0.33 0.51 c 0.19 0.25 D 4.80 5.00 E 5.80 6.20 E1 3.80 MAX 4.00 1.27 BSC e PIN # 1 IDENTIFICATION NOM h 0.25 0.50 L 0.40 1.27 0 8 TOP VIEW D h A1 A c e b L SIDE VIEW END VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MS-012. http://onsemi.com 11 CAT93C56, CAT93C57 PACKAGE DIMENSIONS SOIC-8, 208 mils CASE 751BE-01 ISSUE O SYMBOL MIN NOM 2.03 A E1 E MAX A1 0.05 0.25 b 0.36 0.48 c 0.19 0.25 D 5.13 5.33 E 7.75 8.26 E1 5.13 5.38 1.27 BSC e L 0.51 0.76 0 8 PIN#1 IDENTIFICATION TOP VIEW D A e b q L A1 SIDE VIEW c END VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with EIAJ EDR-7320. http://onsemi.com 12 CAT93C56, CAT93C57 PACKAGE DIMENSIONS TSSOP8, 4.4x3 CASE 948AL-01 ISSUE O b SYMBOL MIN NOM A E1 E MAX 1.20 A1 0.05 A2 0.80 b 0.19 0.15 0.90 1.05 0.30 c 0.09 D 2.90 3.00 3.10 E 6.30 6.40 6.50 E1 4.30 4.40 4.50 e 0.20 0.65 BSC L 1.00 REF L1 0.50 0 0.60 0.75 8 e TOP VIEW D A2 c q1 A A1 L1 SIDE VIEW L END VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MO-153. http://onsemi.com 13 CAT93C56, CAT93C57 PACKAGE DIMENSIONS TDFN8, 2x3 CASE 511AK-01 ISSUE A D A e b E2 E PIN#1 IDENTIFICATION A1 PIN#1 INDEX AREA D2 TOP VIEW SIDE VIEW SYMBOL MIN NOM MAX A 0.70 0.75 0.80 A1 0.00 0.02 0.05 A2 0.45 0.55 0.65 A3 A2 A3 0.20 0.25 0.30 D 1.90 2.00 2.10 D2 1.30 1.40 1.50 E 2.90 3.00 3.10 E2 1.20 1.30 1.40 L BOTTOM VIEW 0.20 REF b e FRONT VIEW 0.50 TYP 0.20 0.30 L 0.40 Notes: (1) All dimensions are in millimeters. (2) Complies with JEDEC MO-229. http://onsemi.com 14 CAT93C56, CAT93C57 PACKAGE DIMENSIONS TDFN8, 3x3 CASE 511AL-01 ISSUE A D A e b L E E2 PIN#1 ID PIN#1 INDEX AREA A1 SIDE VIEW TOP VIEW SYMBOL MIN NOM MAX A 0.70 0.75 0.80 A1 0.00 0.02 0.05 A3 BOTTOM VIEW 0.20 REF b 0.23 0.30 0.37 D 2.90 3.00 3.10 D2 2.20 --- 2.50 E 2.90 3.00 3.10 E2 1.40 --- 1.80 e L D2 A A3 A1 0.65 TYP 0.20 0.30 0.40 Notes: (1) All dimensions are in millimeters. (2) Complies with JEDEC MO-229. http://onsemi.com 15 FRONT VIEW CAT93C56, CAT93C57 Example of Ordering Information CAT93C56, Die Rev. G, New Product Prefix Device # Suffix CAT 93C56 V I -G Temperature Range Company ID Lead Finish G: NiPdAu Blank: Matte-Tin I = Industrial (-40C to +85C) E = Extended (-40C to +125C) Product Number 93C56 T3 Tape & Reel (Note 16) T: Tape & Reel 2: 2,000 Units / Reel (Note 14) 3: 3,000 Units / Reel Package L: PDIP V: SOIC, JEDEC X: SOIC, EIAJ (Note 14) Y: TSSOP VP2: TDFN (2 x 3 mm) 9. The device used in the above example is a CAT93C56VI-GT3 (SOIC, Industrial Temperature, NiPdAu, Tape & Reel). CAT93C56/57, Die Rev. E, Mature Product (CAT93C56, Rev. E - Not Recommended for New Designs) Prefix Device # Suffix CAT 93C56 V -1.8 I Temperature Range Company ID Product Number 93C56 93C57 I = Industrial (-40C to +85C) A = Automotive (-40C to +105C) E = Extended (-40C to +125C) Package L: PDIP V: SOIC, JEDEC W: SOIC, JEDEC X: SOIC, EIAJ (Note 14) Y: TSSOP ZD4: TDFN (3 x 3 mm) T3 -G Lead Finish G: NiPdAu Blank: Matte-Tin Operating Voltage Blank: VCC = 2.5 V to 5.5 V 1.8: VCC = 1.8 V to 5.5 V Rev E (Note 13) Die Revision 93C56: E 93C57: E Tape & Reel (Note 16) T: Tape & Reel 2: 2,000 Units / Reel (Note 14) 3: 3,000 Units / Reel 10. All packages are RoHS-compliant (Lead-free, Halogen-free). 11. The standard lead finish is NiPdAu. 12. The device used in the above example is a CAT93C56VI-1.8-GT3 (SOIC green package, Industrial Temperature, 1.8 Volt to 5.5 Volt Operating Voltage, NiPdAu finish, Tape & Reel). 13. Product die revision letter is marked on top of the package as a suffix to the production date code (e.g., AYWWE). For additional information, please contact your ON Semiconductor sales office. 14. For SOIC, EIAJ (X) package the standard lead finish is Matte-Tin. This package is available in 2,000 pcs/reel, i.e. CAT93C56XI-T2. 15. For additional package and temperature options, please contact your nearest ON Semiconductor sales office. 16. For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 16 CAT93C56, CAT93C57 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 17 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative CAT93C56/D